Can i put junction box in attic

Step 1 - Turn Off the Power. Step 2 - Remove the Old Light Fixture. Step 3 - Find Closest Stud. Step 5 - Attach Junction Box to Stud. Step 6 - Insert Wiring into Junction Box. Step 7 - Wire the Light Fixture. Can junction boxes be covered with insulation? Covering Junction Boxes Even if the insulation doesn't create a fire hazard or render the box inaccessible, it does obscure its location. Some builders consider it safe to completely cover junction boxes in the attic with insulation as long as you mark the positions of the boxes.

Can you spur off a junction box? Spur using a junction box If there is no socket outlet nearby, an alternative is to use a junction box. This is similar to the previous method, but instead of connecting to a socket, a junction box is connected into the ring and the spur cable attached there.

How many connections can be in a junction box? Counting Wires in Electrical Boxes Each switch, outlet, or other device counts as two wires. Does a junction box have to be attached to a stud? Most electrical boxes are attached to a stud before the drywall is even installed. When you add a new box to an old wall, we always try to put it in right next to a stud for solid attachment.

Specialized hardware does exist to allow putting an electrical outlet or switch absolutely anywhere without reference to a stud. Step 4 Drill holes for the junction box. Step 5 Connect the junction box to the outlet. Step 6 Connect the wires to the junction box. Step 7 Connect the lamp. Step 8 Connect the lamp to the junction box. Covers the Junction Boxes Although the insulation does not pose a fire hazard or make the box inaccessible, it hides its location.

Some builders find it safe to completely cover loft junction boxes with insulation, as long as the positions of the boxes are marked. Question about using a junction box If there is no outlet nearby, a junction box can be used as an alternative. This is similar to the previous method, but instead of a socket, a junction box is connected to the ring and the track cable is connected to it.

Most control boxes are assembled with pins before patching. Whenever we put a new box on an old wall, we always try to place it next to a pen for a secure grip. There is special hardware to connect or change absolutely anywhere without reference to a bolt.

If cables need to be extended, a junction box will be required. It must remain available. Overfilling a junction box Laying too many wires in a junction box is not only dangerous but also violates the National Electrical Code. Plastic junction boxes are printed with the approved volume, you may need to calculate by yourself the volume for a steel box.

Turn off the main switch in the breaker box or, if you know the circuit in the junction box, turn off the breaker. Remove the cover from the junction box you are replacing. Remove all clamps from all connections. No, if you do not clean the junction box, it will not comply with the wiring regulations as the cables are not marked in an authorized safe area.

This way you; or any other future owner, will be able to locate them later if need be. The junction boxes that contain splices and are not accessible from the ceiling below should be exposed - not covered by insulation. If enough slack is present in the cables between the boxes, you may be able to raise them up a bit and mount them on trusses or other exposed framing members without having to run new wire. I would suggest that you install access panels in the ceiling for these concealed boxes, and then cover them with insulation.

Not covering them with insulation could lead to moisture problems because the cold attic air will hit warmer air around the un-insulated box which is warmer because the other side of it ceiling is a conditioned space.

Also, in the event you need to access the box, it is easier to access it from the conditioned space and not have to crawl around your attic. Be sure no additional vapor barrier is added over your existing insulation.

I am in the same situation adding some recess lighting. I chose to hold off the installation of the junction box and get some wood to raise it. Reasoning, I was not sure about the code, it's easy to do and will be better for me or anyone who may want to add on later to the box. Some wood, a nail gun or some plates, and some screws and you're ready to go.

So no raising them above insulation or opening ceiling to ad exposed box covers. Come on people. Yes cover them. Sign up to join this community. The best answers are voted up and rise to the top. Stack Overflow for Teams — Collaborate and share knowledge with a private group. Create a free Team What is Teams? Learn more. Can I cover junction boxes in the attic with insulation?

Ask Question. Asked 8 years, 7 months ago. Active 1 year, 8 months ago. Viewed 73k times. Improve this question. Community Bot 1. Evil Elf Evil Elf 3, 8 8 gold badges 37 37 silver badges 48 48 bronze badges.